Rancang Bangun Sistem Moitoring Pada Motor Induksi 3 Phase

Den Anjar Nuri Al Hady; ujang wiharja ujang wiharja

doi:10.61488/jetro.v14i1.779

Penulis

Den Anjar Nuri Al Hady Universitas Krisnadwipayana
ujang wiharja ujang wiharja Universitas Krisnadwipayana

DOI:

https://doi.org/10.61488/jetro.v14i1.779

Kata Kunci:

Node, Blynk, sensor, microcontroller

Abstrak

In industrial manufacturing, electricity is one of the most critical resources for sustaining operations, particularly production activities. Therefore, electrical systems must remain in optimal condition, ideally operating continuously without interruption. Proper maintenance and periodic monitoring are essential to ensure reliability. Failures in production machinery often arise from multiple factors, not only disturbances in the power supply but also external interferences such as animals..

To address these challenges, a Three-Phase Current and Voltage Monitoring Device was developed to facilitate real-time monitoring of all production panels without requiring direct on-site inspection, thereby improving time efficiency. The system employs a NodeMCU microcontroller integrated with a PZEM-004T sensor, utilizing an IoT-based platform via Blynk. The measurement error achieved is approximately 0.54%.

The advantage of this monitoring tool lies in its ability to identify the cause of phase trips when the flowing current exceeds the protection settings, thereby simplifying the analysis of disturbances and enhancing overall system reliability.

Referensi

Teten Dian Hakim, “RANCANG BANGUN SISTEM MONITORING DAN SENSOR JARAK BERBASIS MIKROKONTROLER PADA TEMPAT SAMPAH,” Elektro, vol. 10, no. 1, pp. 1–10, 2022, [Online]. Available: https://jurnalteknik.unkris.ac.id/index.php/jie/article/view/135/135

A. Supriyadi, L. Aditya, and U. Wiharja, “Rancang Bangun Simulasi Parkir Mobil Berbasis Mikrokontroler ESP 8266 dan Monitoring Menggunakan Blynk,” J. Elektro, vol. 13, no. 2, pp. 94–101, 2025.

A. Mustofa and U. Wiharja, “Studi Perbandingan Antara Penggunaan Selenoid Kapiler dan Selenoid Ekspansi pada Mesin Es serta denganPengendaliBlynk,” J. Ampere, vol. 8, no. 2, pp. 95–103, 2023, [Online]. Available: https://jurnal.univpgri-palembang.ac.id/index.php/ampere/article/view/11437/7883

M. A. Hailan, B. M. Albaker, and M. S. Alwan, “Transformation to a smart factory using NodeMCU with Blynk platform,” Indones. J. Electr. Eng. Comput. Sci., vol. 30, no. 1, pp. 237–245, 2023, doi: 10.11591/ijeecs.v30.i1.pp237-245.

N. Naibaho and A. Ramadhan, “Rancang Bangun Alat Deteksi Kebakaran Berbasis Mikrokontroler ESP32 Dengan Energi Surya,” J. Elektro, vol. 13, no. 2, pp. 66–76, 2025.

T. O. Priyono and G. Prasetyo, “Rancang Bangun Sistem Monitoring Berbasis IoT Pada Panel Surya 20 WP Meggunakan Arduino Mega 2560,” 2022.

Tri Sulistyorini, Nelly Sofi, and Erma Sova, “Pemanfaatan Nodemcu Esp8266 Berbasis Android (Blynk) Sebagai Alat Alat Mematikan Dan Menghidupkan Lampu,” J. Ilm. Tek., vol. 1, no. 3, pp. 40–53, 2022, doi: 10.56127/juit.v1i3.334.

B. Kusumo and F. Salam, “Rancang Bangun Sistem Kontrol Dan Alat Monitoring Traffic Light,” J. Elektro, vol. 12, no. 2, 2023.